Incoloy 800 Round Bar, ASTM B408 Incoloy 800HT Round Bars, Incoloy 800 Square Bar, Incoloy 800H Rectangular Bars Manufacturer, Suppliers

Incoloy 800/800H/800HT Round Bars

Incoloy Din 1.4958 Bars, Incoloy 800 Rods, Nickel Alloy 800H Flat Bar, Incoloy® Alloy 800HT Threaded Bar Manufacturer in India.

ASTM B408 Incoloy 800/800H/800HT Round Bars

Inconel UNS N08800/N08810/N08811 Round Bars

Victor Steel is a famous distributor and stockist of Incoloy 800 / 800H / 800HT, which is utilized in quite a few corrosion resisting applications. Incoloy UNS N08800 Hollow Bars retains strength over an extensive temperature variety, appealing for excessive temperature applications in which aluminium and steel could succumb to creep because of thermally brought on crystal vacancies. It has brilliant corrosion resistance to caustic environments. The chromium content material on this Incoloy WNR 1.4876 Hexagonal Bars gives resistance to weaker oxidizing situations. Controlled chemical composition limits of this product is implemented within the nuclear enterprise to put off the threat of strain corrosion cracking via way of means of excessive purity water containing chloride ions.

Incoloy UNS N08810 Triangular Bars has first-rate resistance to corrosion via way of means of dry chlorine and hydrogen chloride gas. It is utilized in heat treating gadget, and gas turbine engine additives. It has right resistance to aqueous corrosion and excessive mechanical strength. The composition of this alloy is a face-centered-cubic solid solution with an excessive degree of metallurgical stability. Incoloy WNR 1.4958 Flat Bars develops a tightly adherent oxide scale which resists even below situations of intense thermal biking. The nickel base of this product, alongside considerable chromium content material, gives resistance to numerous corrosive media and excessive-temperature environments. It has right hot corrosion resistance below oxidizing situations. Incoloy UNS N08811 Square Bars incorporates each chromium and nickel metals as the principle non - iron constituents. It is the standard stainless and is being taken into consideration because the maximum flexible at the side of significantly used steel. It is the standards stainless that you may probable seein terms of fittings on your pans and cookery tools. When deciding on steel that ought to bear corrosive environments, Incoloy WNR 1.4859 Threaded Bars may be usually used. It is much less electrically and thermally conductive than carbon steel and is basically non - magnetic. It gives a few degree of corrosion resistance above and past that of plain steel.

800 Inconel Triangular Bar, Incoloy JIS NCF 800H Black Bar, Incoloy UNS N08800 Square Bar, ASTM B408 Incoloy 800HT Hex Bar Suppliers in India..

ASTM B408 Incoloy 925 Round Bars Specification

Our 800/800H/800HT Incoloy Round bar conforms to NACE MR0175/ISO 15156
Alloy 800/800H/800HT Bar Standard	ASTM B408, AMS 5513, AMS 5511, AMS 5647
Incoloy 800HT Bar Dimensions	EN, DIN, JIS, ASTM, BS, ASME, AISI
Incoloy 800HT Round bar size	Diameter: 3-~800mm
Incoloy 800/800H/800HT Hex Bar size	2-100mm A/F
Alloy 800/800H/800HT Flat bar size	Thickness: 2 -100mm
Alloy 800/800H/800HT Flat bar size	Width: 10 to 500mm
Incoloy 800/800H/800HT Square bar size	4 to 100mm
Alloy 800/800H/800HT Angle bar size	3mm20mm20mm~12mm100mm100mm
Incoloy Alloy 800/800H/800HT Rectangular Bars Section	3.0 to 12.0mm thickness
Incoloy 800/800H/800HT Channel Bar	80 x 40mm to 150 x 75mm section; 5.0 to 6.0mm thickness
ASTM B408 Type 800/800H/800HT Hollow Bar	32mm OD x 16mm ID to 250mm OD x 200mm ID)
Incoloy Alloy 800/800H/800HT Threaded Bar Billet Size	1/2 to 495mm Diameter
Incoloy 800/800H/800HT Rectangular Size	33 x 30mm to 295 x 1066mm
800/800H/800HT Alloy Hex Bars Finish	Cold (bright) drawn, centreless ground, hot rolled, smooth turned, peeled, slit rolled edge, hot rolled annealed, Rough Turned, Bright, Polish, Grinding, Centreless Ground & Black
ASTM B408 Type 800/800H/800HT Hollow Bar Tolerance	H8, H9, H10, H11, H12, H13K9, K10, K11, K12 or as per clients’ requirements
JIS NCF 800/800H/800HT T-Bar Surface	Bright, Hot Rolled Pickled, Cold Drawn, Sand Blasting Finished, Polished, Hairline
Rolled Incoloy 800/800H/800HT Flat Bars Condition	Hardened & tempered, annealed
ASTM B408 Type 800/800H/800HT Cold Rolled Bar Technique	800HT Incoloy Alloy Hot Rolled, Cold Drawn, Cold Rolled, Forged Round Bar, Rod
Alloy 800/800H/800HT Rod Processing	Bar cutting to 650mm
800/800H/800HT Incoloy Rounds Bar Form	Round, Rod, T-Bar, Channel Bar, Precision Ground Bar, Flat Bar, Square, Blocks, Round Rod, Rings, Hollow, Triangle, Rectangle, Hex (A/F), Threaded, Half Round Bar, Profiles, Billet, Ingot, I/H Bar, Forging etc.

Incoloy 800/800H/800HT Round Bars

Incoloy 800/800H/800HT Flat Bars

Incoloy 800/800H/800HT Hexagone Bars

Incoloy 800/800H/800HT Threaded Rods

Incoloy 800/800H/800HT Reinforcing Rods

Incoloy 800/800H/800HT Rebar

Incoloy 800/800H/800HT Hollow Bar

Incoloy 800/800H/800HT Round Edge Flat Bar

Incoloy 800/800H/800HT Square Bars

Incoloy 800/800H/800HT Rectangular Bar

Incoloy 800/800H/800HT Triangle Bar

Incoloy 800/800H/800HT Tig Bar

ASTM B408 Incoloy 800/800H/800HT Round Bars Equivalent Grade

STANDARD	WERKSTOFF NR.	UNS	JIS	BS	GOST	AFNOR	EN	OR
Incoloy 800	1.4876	N08800	NCF 800	NA 15	ЭИ670	Z8NC32-21	X10NiCrAlTi32-20	XH32T
Incoloy 800H	1.4958 / 1.4876	N08810	NCF 800H	NA 15(H)	ЭИ670	Z8NC33-21	X5NiCrAlTi31-20	XH32T
Incoloy 800HT	1.4859 / 1.4876	N08811	NCF 800HT	NA 15(HT)	ЭИ670	-	X8NiCrAlTi32-21	XH32T

Incoloy 800/800H/800HT Round Bars Chemical Composition

Grade	C	Mn	Si	S	Cu	Fe	Ni	Cr	Al	Ti
800	0.10 max	1.50 max	1.00 max	0.015 max	0.75 max	39.50 min	30.00 – 35.00	19.00 – 23.00	0.15 – 0.60	0.15 – 0.60
800H	0.05 – 0.10	1.50 max	1.00 max	0.015 max	0.75 max	39.50 min	30.00 – 35.00	19.00 – 23.00	0.15 – 0.60	0.15 – 0.60
800HT	0.06 – 0.10	1.50 max	1.00 max	0.015 max	0.75 max	39.50 min	30.00 – 35.00	19.00 – 23.00	0.15 – 0.60ᴬ	0.15 – 0.60ᴬ

Incoloy 800/800H/800HT Round Bars Mechanical Properties

Element	Density	Melting Point	Tensile Strength	Yield Strength (0.2%Offset)	Elongation
800 / 800H / 800HT	7.94 g/cm3	1385 °C (2525 °F)	Psi – 75,000 , MPa – 520	Psi – 30,000 , MPa – 205	30 %

Processing Of Incoloy 800/800H/800HT Bars & Rods

Round bar Cutting	Products cut include Round bars, Flat bars, Hex bars, Square bars, Tubing and Hollow bars, Pipe, Angles, channels, Beams and Tees. Thickness range is 1/16″ to 28″ diameter
Round bar Production Cutting	We can provide production cutting for product diameters up to 4″. We utilize Amanda Production Equipment to achieve these precision cuts with tight tolerances.
Round bar Polishing	Products polished included all tubular products, with OD & ID polishing available, Round bars, Square bars, Hex & Flat bars, Angles, Uneven Leg Angles, beams, and other shapes.

ASTM B408 Incoloy 800/800H/800HT Bars & Rods Forms & Availability

Products		Size
ASTM B408 800/800H/800HT Inconel Alloy Rolled Bar	ASTM B408 800/800H/800HT Alloy Hot Rolled Bar	Sizes 3 - 800mm
ASTM B408 800/800H/800HT Alloy Cold Rolled Bar	ASTM B408 800/800H/800HT Inconel Forged Bar
ASTM B408 800/800H/800HT Inconel Continuous Cast Bar	ASTM B408 800/800H/800HT Inconel Alloy Rods
ASTM B408 800/800H/800HT Inconel Alloy Annealed Bar	ASTM B408 800/800H/800HT Inconel Alloy Normalized Bar
ASTM B408 800/800H/800HT Inconel Quenched & Tempered Bar	ASTM B408 800/800H/800HT Inconel Alloy Hardened & Tempered Bar
ASTM B408 800/800H/800HT Inconel Alloy Black Bar	ASTM B408 800/800H/800HT Inconel Bright Bar
ASTM B408 800/800H/800HT Inconel Peeled Bar	ASTM B408 800/800H/800HT Inconel Alloy Grinded Machined Bar
ASTM B408 800/800H/800HT Inconel Alloy Shaft	ASTM B408 800/800H/800HT Inconel Alloy Polished Bar
ASTM B408 800/800H/800HT Inconel Alloy Cold Finish Round Bar	ASTM B408 800/800H/800HT Nickel Alloy Half Round Bar

ASTM B408 Incoloy 800/800H/800HT Round Bars Standards

Standard	Description
ASTM B408	Specification for Inconel Bars and Shapes
ASTM A314	Specification for Inconel Billets and Bars for Forging
ASTM A493	Specification for Inconel Wire and Wire Rods for Cold Heading and Cold Forging
ASTM A564	Specification for Hot-Rolled And Cold-Finished Age-Hardening Inconel Bars and Shapes
ASTM A565	Specification for Martensitic Inconel Bars, Forgings, and Forging Stock for High Temperature Service
ASTM A582	Specification for Free Machining Inconel Bars
ASTM A666	Specification For Annealed or Cold-Worked Inconel Flat Bar
ASTM A484	Standard specification general requirements for Inconel and heat-resisting bars, billets and forgings.
ASTM A476	Standard specification for Inconel and heat-resisting steel bars and shapes for used in boilers and other pressure vessels.

Inconel 800/800H/800HT Round Bar Size Chart

Size & Dimensions of Incoloy 800/800H/800HT round bar
Metric		US Bar		ASTM/ Canadian		Japanese
Bar Size	Diam. (mm)	Bar Size	Diam. (Inch)	Bar Size	Diam. (mm2)	Bar Size	Diam. (mm)
5	5	#2	0.250	10M	100	6	6
5.5	5.5	#3	0.375	15M	200	10	10
6	6	#4	0.500	20M	300	13	13
7	7	#5	0.400	25M	500	16	16
8	8	#6	0.750	30M	700	19	19
9	9	#7	0.875	35M	1000	22	22
10	10	#8	1.000	45M	1500	25	25
11	11	#9	1.125	55M	2500	29	29
12	12	#10	1.250			32	32
14	14	#11	1.375			35	35
16	16	#12	1.500			38	38
18	18	#13	1.400			41	41
20	20	#14	1.750			44	44
22	22	#15	1.875			48	48
25	25	#16	2.000			51	51
28	28	#18	2.250			57	57
32	32
36	36
40	40
44	44
50	50

Weight Chart Incoloy 800/800H/800HT Round Bar

Size	Kgs / Foot	Kgs / Mtr	Size	Kgs / Foot	Kgs / Mtr	Size	Kgs / Foot	Kgs / Mtr
Round Bar
3mm	0.017	0.055	20mm	0.753	2.470	3″	10.900	35.762
1/8″	0.019	0.062	22mm	0.908	2.979	3-1/4″	12.800	41.996
5/32″	0.029	0.095	7/8″	0.926	3.038	3-1/2″	14.850	48.772
4mm	0.030	0.098	24mm	1.080	3.543	3-3/4″	17.001	55.780
3/16″	0.043	0.141	25mm	1.180	3.871	4″	19.306	63.340
5mm	0.047	0.154	1″	1.210	3.970	4-1/4″	21.908	72.249
7/32″	0.058	0.190	26mm	1.271	4.170	4-1/2″	24.4487	80.340
6mm	0.068	0.223	27mm	1.368	4.490	4-3/4″	27.366	90.249
1/4″	0.076	0.249	1-1/8″	1.534	5.033	5″	30.461	99.940
7mm	0.091	0.298	30mm	1.691	5.548	5-1/2″	36.690	121.000
5/16″	0.118	0.387	1-1/4″	1.924	6.349	6″	43.860	143.900
8mm	0.120	0.398	32mm	1.894	6.314	6-1/2″	51.093	167.630
9mm	0.152	0.498	1-3/8″	2.303	7.550	7″	59.432	196.000
3/8″	0.170	0.557	35mm	2.390	7.553	7-1/2″	68.226	225.000
10mm	0.189	0.620	36mm	2.438	7.999	8″	77.586	254.55
11mm	0.228	0.748	38mm	2.792	8.903	10″	121.048	397.140
7/16″	0.232	0.761	1-1/2″	2.715	8.951
12mm	0.271	0.889	40mm	3.009	9.872
1/2″	0.303	0.994	1-5/8″	3.200	10.449
13mm	0.318	1.043	1-3/4″	3.712	12.179
14mm	0.368	1.207	45mm	3.807	12.555
9/16″	0.383	1.256	1-7/8″	4.260	13.977
15mm	0.424	1.391	48mm	4.330	14.205
5/8″	0.473	1.551	50mm	4.698	15.414
16mm	0.481	1.578	2″	4.848	15.906
17mm	0.543	1.791	2-1/8″	5.475	17.963
11/16″	0.573	1.880	2-1/4″	6.135	20.128
18mm	0.610	2.001	60mm	6.768	22.205
3/4″	0.682	2.237	2-3/8″	6.838	22.435
			2-1/2″	7.576	24.856
			2-5/8″	8.354	27.409
			2-3/4″	9.169	30.083