Copper Nickel 90/10 Shim Sheets, Cupro Nickel UNS C70600 Plates, ASME SB122 Copper Nickel 90/10 Sheet, 90/10 Cu-ni Shim Sheet Manufacturer, Suppliers

Copper Nickel 90/10 Sheets & Plates

Cupro Nickel 90/10 Coils, Copper Nickel UNS C70600 Plates, Cu-Ni 90/10 Sheets, ASTM B122 90/10 Cu-ni Cold Rolled Plates Manufacturer in India.

Copper Nickel 90/10 Sheets & Plates

Victor Steel is a well-known distributor and supplier of Copper Nickel 90 / 10 Sheets & Plates, which has extra quantities of copper and nickel than different alloys. Cupro nickel 90 / 10 Sheets & Platesis not unusual to the petroleum refining industries. It is regularly utilized in Aircraft collector rings, Aircraft exhaust stacks, Boiler casing, and greater. Columbium-tantalum on this steel carbides precipitates in the grains as opposed to forming on the grain boundaries. It may be without problems welded and processed through standard save fabrication practices. The use of sluggish speeds and steady nice feeds on this alloy will decrease this alloy's tendency to work harden. It is classified as a multi-cause austenitic stainless steel - the alloy gives amazing heat and corrosion resistance. It has a considerably better coefficient of thermal growth as non-alloyed steel.

Higher carbon of this Copper Nickel UNS C70600 Sheets lets in for higher excessive temperature creep properties. In addition, it forms any other institution called precipitation-hardened steels, which might be an aggregate of martensitic and austenitic steels. It is used to make radiant super-heaters, boiler tubes, excessive strain steam pipe, and fashionable refinery piping. Due to the stabilization with niobium, it has the corrosion resistance at excessive temperatures as its essential characteristic. Tantalum on this steel takes place in nature together with columbium and consequently it can be stated that each are components to this alloy. Copper Nickel WNR 2.0872 Plates does have very enormous contents of the excessive cost components nickel and molybdenum. It has additionally properly resistance towards crevice corrosion, pitting corrosion, strain corrosion cracking and inter-crystalline corrosion. So it isn't always vital to anneal this steel or make a comparable operation beforehand. It gives higher erosion resistance, although it doesn’t system and wishes specialised equipment to be as it should be altered into the critical shapes. For most corrosion resistance on this alloy, it's far endorsed to apply filler metals of same or better alloy content material. It has a better resistance to pitting and crevice corrosion this is needed.

90/10 Copper Nickel Hot Rolled Plates, Cupro Nickel 90/10 Sheets, ASME SB122 Cu-ni 90/10 Shim Sheets, Cu-Ni Werkstoff No 2.0872 Sheets Supplier in Mumbai, India.

Copper cu-ni-90-10 sheets plates Specification

Copper cu-ni-90-10 Sheets & Plates Specifications	ASTM B127 / ASME SB127, BS EN 10088-2, en 10028-7, IS 6911
Copper cu-ni-90-10 Sheets & Plates Dimension Standard	MSRR, AMS, BS, JIS, AISI, ASTM, GB, DIN, EN, etc
Copper cu-ni-90-10 Sheets & Plates Size Range	Cold rolled ASME SB127 Grade cu-ni-90-10 Copper Sheet 0.5-6.4 mm Hot rolled ASME SB127 Grade cu-ni-90-10 Copper Sheet 3.0–10.0 mm
Copper cu-ni-90-10 Copper Sheets & Plates Width	1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc
Copper cu-ni-90-10 Sheets & Plates Length	2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc
Copper cu-ni-90-10 Sheets & Plates Thickness	0.3 mm to 120 mm
International Standard of Copper cu-ni-90-10 Sheets & Plates	ASTM A480 ASTM A959 ASME IID EN ISO 9445 EN ISO 18286 EN 10051 EN 10088-1 ISO 15510
Tolerances (width / thickness) of Copper cu-ni-90-10 Sheets & Plates	EN 10258/ DIN 59381) EN 10151 ASME SB127 cu-ni-90-10 Copper Strips EN 10088 SA -240-cu-ni-90-10 Strips
Finish of Copper cu-ni-90-10 Sheets & Plates	2B, 2D, BA NO (8), Cold rolled sheet (CR), Hot rolled plate (HR), SATIN (Met with Plastic Coated), No.1 finish hot rolled, 1D, 2B, No.4, BA, 8K, satin, hairline, brush, mirror etc.
Hardness	Half Hard, Soft, Hard, Quarter Hard, Spring Hard
Form	Sheet, Plate, Strip, Flats, Clad Plate, Coils, Foils, Plain Sheet, Flat Shim, Flat Sheet, Shim Sheet, Rolling Sheet, Rolling Plate, Rolls, Blank (Circle), soft annealed, descaled, tread plate, sheared, annealed, Checker Plate
Value Added Service	Cladding, Heat Treatment, Annealed, Pickling, Polish, Rolling, Cutting, Bending, Forging, Minor Fabrication Etc.
Dealers & Distributor of	SAIL, ESSAR, JINDAL, TATA, BHUSHAN, INDIAN, POSCO, JISCO, TISCO, LISCO, BAOSTEEL IMPORTED material
Copper cu-ni-90-10 Profiling	Plasma Plate Cutting Laser Plate Cutting Oxy-propane Flame Cutting

Copper 90/10 Sheets & Plates

Copper 90/10 chequred Sheets & Plates

Copper 90/10 Perforated Sheets

Copper 90/10 Strips & Foils

Copper 90/10 Shim Sheets

Copper 90/10 Decorative Sheets

Copper 90/10 Polished Plates

Copper 90/10 Blamk (circle) Sheet

Copper 90/10 Sheets & Plates Equivalent Grade

STANDARD	WERKSTOFF NR.	UNS	JIS	BS	GOST	AFNOR	EN
Copper 90/10	2.4360	N04400	NW 4400	NA 13	МНЖМц 28-2,5-1,5	NU-30M	NiCu30Fe

Copper 90/10 Sheets & Plates Chemical Composition

Grade	C	Mn	Si	S	Cu	Fe	Ni
Copper 90/10	0.30 max	2.00 max	0.50 max	0.024 max	28.00 – 34.00	2.50 max	63.00 min

Copper 90/10 Sheets & Plates Mechanical Properties

Element	Density	Melting Point	Tensile Strength	Yield Strength (0.2%Offset)	Elongation
Copper 90/10	8.8 g/cm3	1350 °C (2460 °F)	Psi – 80,000 , MPa – 550	Psi – 35,000 , MPa – 240	40 %

Copper 90/10 Sheets & Plates Finishes

Surface Finish	Definition	Application
2B	Those finished, after cold rolling, by heat treatment, pickling or other equivalent treatment and lastly by cold rolling to given appropriate luster.	Medical equipment, Food industry, Construction material, Kitchen utensils.
BA	Those processed with bright heat treatment after cold rolling.	Kitchen utensils, Electric equipment, Building construction.
NO.3	Those finished by polishing with No.100 to No.120 abrasives specified in JIS R4001.	Kitchen utensils, Building construction.
NO.4	Those finished by polishing with No.150 to No.180 abrasives specified in JIS R6001.	Kitchen utensils, Building construction, Medical equipment.
HL	Those finished polishing so as to give continuous polishing streaks by using abrasive of suitable grain size.	Building Construction.
NO.1	The surface finished by heat treatment and pickling or processes corresponding there to after hot rolling.	Chemical tank, pipe