Super Duplex Sheets & Plates
Super Duplex Steel S32750 Plates, Super Duplex 2507 Hot Rolled Plates, Super Duplex Stainles Steel S32760 Chequered, SDSS UNS S32750 Sheets Exporter in India.
Victor Steel is a well-known seller and manufacturer of Super Duplex Steel S32750 / S32760 Sheets & Plates, which presents amazing resistance to oxidation below mildly cyclic situations.Pure factors on this Super Duplex 2507 Sheets continually react with the encompassing surroundings that is why so few factors are certainly determined of their natural shape. Iron isn't any exception. It is an austenitic chromium-nickel stainless and heat-resisting steel with advanced corrosion resistance compared to different. In moist or humid situations iron reacts with the oxygen on this alloy, this contained water to shape iron oxide additionally referred to as rust. This therefore completed alloy are regularly presented to the market 'twin certified' to grade designations as they are able to then be used for fabrications specifying both grade, inside a particular standard.
Alloy 2507 Plates has excellent corrosion resistance and right aqueous corrosion resistance. It is used regularly in carburizing atmospheres which are not unusual in petrochemical industries. The excessive chromium and nickel contents of this steel offer similar corrosion resistance. It is an austenitic alloy evolved to be used in excessive temperature corrosion resistant applications. It has advanced resistance to oxidation and the retention of a bigger fraction of room temperature strength than the not unusual austenitic alloys. It is utilized in food processing equipment, especially in milk processing, wine making and beer brewing. In addition, Super Duplex WNR 1.4410 Sheets is used at temperatures as much as 1150 Degree C in non-stop range, and 1035 Degree C in intermittent range. It is an incredibly alloyed austenitic stainless steel used for excessive temperature application. It is normally used for extended temperature applications as its excessive chromium and nickel content material offer strong corrosion resistance. Further, it is used for significantly inured to the impact of sulphurous gases, specifically above 900 Degree C, could be very low. They are weldable and formable, and are all changes of the chromium and nickel austenitic alloy. Higher resistance of these products to pitting and crevice corrosion is required, in chloride environments.
SDSS DIN 1.4410 Plates, Super Duplex S32760 Perforated Sheets, Super Duplex Stainless Steel S32750 Cold Rolled Plates, Super Duplex 2507 Shim Sheets Manufacturer in India.
Super DUPLEX STEEL Sheets & Plates Specification
Sheets & Plates Specifications | ASTM A240 / ASME SA240, BS EN 10088-2, en 10028-7, IS 6911 |
---|---|
Sheets & Plates Dimension Standard | MSRR, AMS, BS, JIS, AISI, ASTM, GB, DIN, EN, etc |
Super Duplex Steel Sheets & Plates Size Range | Cold rolled ASME SA240 Grade Super Duplex Steel Sheet 0.5-6.4 mm Hot rolled ASME SA240 Grade Super Duplex Steel Sheet 3.0–10.0 mm |
Super Duplex Steel Sheets & Plates Width | 1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc |
Super Duplex Steel Sheets & Plates Length | 2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc |
Super Duplex Steel Sheets & Plates Thickness | 0.3 mm to 120 mm |
International Standard of Super Duplex Steel Sheets & Plates | ASTM A480 ASTM A959 ASME IID EN ISO 9445 EN ISO 18286 EN 10051 EN 10088-1 ISO 15510 |
Tolerances (width / thickness) of Super Duplex Steel Sheets & Plates | EN 10258/ DIN 59381) EN 10151 ASME SA240 Super Duplex Steel Strips EN 10088 SA -240-Strips |
Finish of Super Duplex Steel Sheets & Plates | 2B, 2D, BA NO (8), Cold rolled sheet (CR), Hot rolled plate (HR), SATIN (Met with Plastic Coated), No.1 finish hot rolled, 1D, 2B, No.4, BA, 8K, satin, hairline, brush, mirror etc. |
Hardness | Half Hard, Soft, Hard, Quarter Hard, Spring Hard |
Form | Sheet, Plate, Strip, Flats, Clad Plate, Coils, Foils, Plain Sheet, Flat Shim, Flat Sheet, Shim Sheet, Rolling Sheet, Rolling Plate, Rolls, Blank (Circle), soft annealed, descaled, tread plate, sheared, annealed, Checker Plate |
Value Added Service | Cladding, Heat Treatment, Annealed, Pickling, Polish, Rolling, Cutting, Bending, Forging, Minor Fabrication Etc. |
Dealers & Distributor of | SAIL, ESSAR, JINDAL, TATA, BHUSHAN, INDIAN, POSCO, JISCO, TISCO, LISCO, BAOSTEEL IMPORTED material |
Super Duplex Steel Profiling | Plasma Plate Cutting Laser Plate Cutting Oxy-propane Flame Cutting |
Super Duplex Steel Sheets & Plates
Super Duplex Steel chequred Sheets & Plates
Super Duplex Steel 310/310S Coils
Super Duplex Steel Strips & Foils
Super Duplex Steel Shim Sheets
Super Duplex Steel Perforated Sheets
Super Duplex Steel Decorative Sheets
Super Duplex Steel Polished Plates
Super Duplex Steel Hairline Finish Sheets
Super Duplex Steel Mirror Finish Sheets
Super Duplex Steel Hot Rolled Sheet
Super Duplex Steel Blamk (circle) Sheet
Super Duplex Steel Sheets & Plates Finishes
Surface Finish | Definition | Application |
---|---|---|
2B | Those finished, after cold rolling, by heat treatment, pickling or other equivalent treatment and lastly by cold rolling to given appropriate luster. | Medical equipment, Food industry, Construction material, Kitchen utensils. |
BA | Those processed with bright heat treatment after cold rolling. | Kitchen utensils, Electric equipment, Building construction. |
NO.3 | Those finished by polishing with No.100 to No.120 abrasives specified in JIS R4001. | Kitchen utensils, Building construction. |
NO.4 | Those finished by polishing with No.150 to No.180 abrasives specified in JIS R6001. | Kitchen utensils, Building construction, Medical equipment. |
HL | Those finished polishing so as to give continuous polishing streaks by using abrasive of suitable grain size. | Building Construction. |
NO.1 | The surface finished by heat treatment and pickling or processes corresponding there to after hot rolling. | Chemical tank, pipe |
Other Types of Super Duplex Sheets & Plates
- SDSS UNS S32750 Sheets Stockholder
- Super Duplex Grade S32760 Coils
- ASME A240 SDSS S32750 Perforated Sheets
- Super Duplex Steel S32760 Sheets & Plates
- Super Duplex 2507 Plates Distributors
- Super Duplex Grade S32750 Sheets Stockiest
- Super Duplex S32750 Plates Supplier
- ASTM A240 SDSS S32760 Sheets
- Super Duplex SAF 2507 Perforated Coils
- Super Duplex Grade S32750 Coils Distributors
- Super Duplex Stainless Steel S32760 Sheets
- SDSS DIN 1.4410 Slatting Coils Stocks