Stainless Steel 347/347H Pipe Fittings
Stainless Steel 347 Stubend, SS DIN 1.4550 Reducer, 347H Stainless Steel Pipe Elbow, SS 347 Equal Tee, Ready Stock of X6CrNiNb18-10 SS Buttweld Elbow, ASTM A403 SS 347H Lateral Tee Manufacturer in Mumbai, India, Saudi Arabia, Qatar, Kingdom Of Bahrain.
Victor Steel is anacknowledged supplier and seller of Stainless Steel 347 / 347H Pipe Fittings, which must be emphasised that these alloys may be machined the usage of traditional manufacturing strategies at satisfactory rates.Stainless Steel UNS S34700End Cap Pipe Fittings is an alloy with excessive strength and top notch corrosion resistance in a number of media along with sea water. This product has excessive strength and top notch corrosion resistance in a number of acidic and alkaline environments and especially appropriate for lowering situations.Normally utilized in numerous applications, this Stainless Steel WNR 1.4550 Dish Cap Pipe Fittings is broadly used for system within the manufacturing of oil and gas. This steel have a more tendency in the direction of strain-corrosion cracking in a few environments while within the age-hardened circumstance.
Fouling on this Alloy 347 Cross Pipe Fittings might also additionally arise accompanied via way of means of pitting however this pitting slows down after a reasonably speedy preliminary attack. Strength and hardness on this steel boom with most effective moderate impairment of ductility or effect resistance. Stainless Steel UNS S34709 Elbow Pipe Fittings has excessive tensile properties as much as approximately 650 Degree C (1200 Degree F). Machining of this steel is simplest within the annealed circumstance consequently the fine exercise could be to system oversize, age-harden, then end to size. For hot-finished products like this Stainless Steel WNR 1.4961 45-Degree Pipe Fittings, solution annealing is accomplished at 1800 Degree F (980 Degree C). The magnetic film on this steel may be eliminated via way of means of pickling or vibrant dipping in acid. This steel may be further strengthened via way of means of cold working previous to precipitation hardening. Alloy 347H 90-Degree Elbow Pipe Fittings has allowing fabrications by means of sound welds to be constructed, mainly within the caustic awareness sector. It has a low work-hardening rate and so is utilized in Paper Production. The presence of chlorates on this product should be stored to a minimum, as they boost up the rate of attack.
Grade 347 SS Pipe Fittings Dealer, Stainless Steel 347H Cross, SS UNS S34700 Buttweld Cross, ASME SA403 WP347H Collar Pipe Fittings Suppliers in Mumbai, India, Qatar, France, Russia.
ANSI B16.9 Stainless Steel 347/347H Pipe Fittings Specification
347 / 347H Pipe Fittings Specifications | ASTM A403/ ASME SA403 |
---|---|
347 / 347H SS Pipe Fittings size | 347 / 347H Seamless Butt Weld Fittings : 1/2" - 10" 347 / 347H Welded Butt Weld Fittings : 1/2" - 48" |
SS 347 / 347H Pipe Fittings Dimensions | ASME/ANSI B16.9, ASME B16.28, MSS-SP-43, BS4504, BS4504, BS1560, BS10 |
Stainless Steel 347 / 347H Buttweld Fittings Thickness | SCH10, SCH20, SCH30, STD SCH40, SCH60, XS, SCH 80, SCH 100, SCH 120, SCH 140, SCH 160, XXS available with NACE MR 01-75 |
347 / 347H Buttweld Pipe FittingsType | DN15-DN1200 |
ASTM A403 347 / 347H Buttweld Fitting Connection | Welding |
Bending Radius | R=1D, 2D, 3D, 5D, 6D, 8D, 10D or Custom ASTM A403 Grade WP347 / 347H Pipe Fitting |
Size Range | ½" NB to 24" NB in Sch 10s, 40s, 80s, 160s, XXS. (DN6~DN100) ASTM A403 WP 347 / 347H Buttweld Fitting |
ASTM A403 WP347 / 347H Buttweld Fittings Manufacturing process | Push, Press, Forge, Cast, etc. |
347 / 347H Stainless Steel Buttweld Pipe Fittings Test Certificates | EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc |
SA 403 WP347 / 347H Pipe Fittings Origin & Mills | Japanese, Indian, USA, Korean, European, Ukraine, Russian |
Specialized manufacturer of | SS UNS S34700, S34709 90º Elbows, 45º Elbows, Tees, Cross, Reducer, Pipe Cap, Stub End, Pipe Bend |
We provide Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2, Test Certificates certifying NACE MR0103, NACE MR0175 |
Stainless Stel 347/347H Cross
Stainless Stel 347/347H Stub End
Stainless Stel 347/347H Tee
Stainless Stel 347/347H 45 deg Elbow
Stainless Stel 347/347H Concentric Reducer
Stainless Stel 347/347H Eccentric Reducer
Stainless Stel 347/347H Pipe Cap
Stainless Stel 347/347H Pipe Nipples
Stainless Stel 347/347H Pipe Bend
Stainless Stel 347/347H Pipe Collar
Stainless Stel 347/347H Lateral Tee
Stainless Stel 347/347H 90 Deg Elbow
Stainless Steel A403 347/347H Pipe Fittings Equivalent Grade Specification
STANDARD | WERKSTOFF NR. | UNS | JIS | GOST | EN |
SS 347 | 1.4550 | S34700 | SUS 347 | 08Ch18N12B | X6CrNiNb18-10 |
SS 347H | 1.4961 | S34709 | SUS 347H | - | X6CrNiNb18-12 |
Stainless Steel A403 347/347H Pipe Fittings Chemical Composition
Grade | C | Mn | Si | P | S | Cr | Cb | Ni | Fe |
SS 347 | 0.08 max | 2.0 max | 1.0 max | 0.045 max | 0.030 max | 17.00 - 20.00 | 10xC – 1.10 | 9.00 - 13.00 | 62.74 min |
SS 347H | 0.04 – 0.10 | 2.0 max | 1.0 max | 0.045 max | 0.030 max | 17.00 - 19.00 | 8xC – 1.10 | 9.0 -13.0 | 63.72 min |
Stainless Steel A403 347/347H Pipe Fittings Mechanical Properties
Density | Melting Point | Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
8.0 g/cm3 | 1454 °C (2650 °F) | Psi – 75000 , MPa – 515 | Psi – 30000 , MPa – 205 | 35 % |
A403 347/347H SS Butt weld Pipe Fittings Dimensions Standard
Nominal Pipe Size |
Outside Diameter |
Caps | Straight Tees | Straight Crosses | Stub Ends | |||
---|---|---|---|---|---|---|---|---|
(inches) | (mm) | (inches) | Length (inches) |
Center to End (inches) |
Center to End (inches) |
Lap Diameter (inches) |
Long Length (inches) |
Short Length (inches) |
1/2 | 21.3 | 0.840 | 1 | 1 | – | 1 3/8 | 3 | 2 |
3/4 | 26.7 | 1.050 | 1 | 1 1/8 | – | 1 11/16 | 3 | 2 |
1 | 33.4 | 1.315 | 1 1/2 | 1 1/2 | 1 1/2 | 2 | 4 | 2 |
1 1/4 | 42.2 | 1.660 | 1 1/2 | 1 7/8 | 1 7/8 | 2 1/2 | 4 | 2 |
1 1/2 | 48.3 | 1.900 | 1 1/2 | 2 1/4 | 2 1/4 | 2 7/8 | 4 | 2 |
2 | 60.3 | 2.375 | 1 1/2 | 2 1/2 | 2 1/2 | 3 5/8 | 6 | 2 1/2 |
2 1/2 | 73.0 | 2.875 | 1 1/2 | 3 | 3 | 4 1/8 | 6 | 2 1/2 |
3 | 88.9 | 3.500 | 2 | 3 3/8 | 3 3/8 | 5 | 6 | 2 1/2 |
3 1/2 | 101.6 | 4.000 | 2 1/2 | 3 3/4 | 3 3/4 | 5 1/2 | 6 | 3 |
4 | 114.3 | 4.500 | 2 1/2 | 4 1/8 | 4 1/8 | 6 3/16 | 6 | 3 |
5 | 141.3 | 5.563 | 3 | 4 7/8 | 4 7/8 | 7 5/16 | 8 | 3 |
6 | 168.3 | 6.625 | 3 1/2 | 5 5/8 | 5 5/8 | 8 1/2 | 8 | 3 1/2 |
8 | 219.1 | 8.625 | 4 | 7 | 7 | 10 5/8 | 8 | 4 |
10 | 273.1 | 10.750 | 5 | 8 1/2 | 8 1/2 | 12 3/4 | 10 | 5 |
12 | 323.9 | 12.750 | 6 | 10 | 10 | 15 | 10 | 6 |
Stainless Steel 347/347H Pipe Fittings Standard
Standard Code | Standard Name |
---|---|
American Steel Pipe Fittings Standard | |
ANSI ASME SA-403 | Forged Durimet pipe fittings |
ANSI ASME B16.9 | Factory-Made wrought steel pipe fittings |
ANSI ASME B16.28 | Wrought steel butt-welding short radius elbows and returns |
ISO 5251 | Stainless steel butt-welding fittings |
MSS SP-43 | Wrought stainless steel butt-welding fittings |
MSS SP-75 | Forging butt-welding fittings |
German Steel Pipe Fittings Standard | |
DIN 2605 | Steel butt-welding pipe fittings.elbows and bends |
DIN 2615 | Steel butt-welding pipe fittings.tees |
DIN 2616 | Steel butt-welding pipe fittings.reducers |
DIN 2617 | Steel butt-welding pipe fittings.caps |
Japanese Steel Pipe Fittings Standard | |
JIS B2311 | Universal steel butt-welding pipe fittings |
JIS B2312 | Steel butt-welding pipe fittings |
JIS B2313 | Steel plate butt-welding pipe fittings |
Other Steel Pipe Fittings Standard | |
EN 1025 | 3 Butt-welding pipe fittings |
Manufacturing Standards of Stainless Steel 347/347H Pipe Fittings
ASME B16.9 ASTM A403 347/347H Pipe Fittings | Factory-Made Wrought Buttwelding Fittings | Long Radius Elbows, Long Radius Reducing Elbows, Long Radius Returns, Short Radius Elbows, Short Radius 180-deg Rerurns, 3D elbows, Straight Tees, Straight Crosses, Reducing Outlet Tees, Reducing Outlet Crosses, Lap Joint Stub Ends, Caps, Reducers |
ASME B16.28 | Short Radius Elbows, Short Radius 180-deg Returns | |
MSS SP43 | Wrought and Fabricated Butt-Welding Fittings for Low Pressure, Corrosion Resistant Applications | Long Radius Elbows, Straight and Reducing-on-the-Outlet Tees, Lap Joint Stub ends, caps, long radius 180 Degree returns, concentric reducers, eccentric reducers |
Mss SP75 | Long Radius Elbows, 3R elbows, straight tees, reducing outlet tees, caps, reducers |
Other Types of Stainless Steel 347/347H Pipe Fittings
- Stainless Steel 347H 90° LR Elbow
- SS UNS S34700 Pipe Reducers
- 347 Stainless Steel Seamless Pipe Fittings
- ASTM A403 WP347H Stainless Steel Caps
- SS X6CrNiNb18-12 Equal Cross Supplier
- MSS SP-43 Stainless Steel 347 Stub End
- 347 Stainless Steel Seamless Reducing Tee
- SS DIN 1.4550 Stub End Exporter
- Stainless Steel 347H Seamless Fittings
- X6CrNiNb18-10 SS 90° Seamless Elbow Dealer
- SUS 347 Seamless Buttweld Fittings
- WP347H SS Two Halve Butt weld Fittings