Duplex Steel UNS S31803/S32205 Fasteners
Duplex Stainless Steel S31803 Fasteners, DSS UNS S32205 Threaded Stud, Duplex 2205 Allot Eye Bolts, DSS S31803 Foundation Bolts Manufacturer in Mumbai, India.
Duplex Steel UNS S31803 Fasteners
Duplex Steel UNS S32205 Fasteners
Duplex Steel 2205 Fasteners
Victor Steel is a well-known distributor and manufacturer of Duplex Steel UNS S31803 / S32205 Fasteners, which are non-corrosive and feature excessive sturdiness and tensile strength. Duplex Steel 2205 Washers have were given unique sizes, grades, instructions and standards that finally lead them to very famous amongst our buyers. It gives a surprisingly sturdy, dependable and tight quintessential line system, where these forms of fittings stay unaffected with the aid of using thermal distortion, vibration and shock. It is usually utilized in noncritical and low-cost applications like fire protection, commercial cooling water and domestic water structures. They are in large part used for small pipe diameters, with the aid of using and big for piping whose nominal diameter is smaller. They are normally made from malleable iron or solid gray, bronze or solid brass, or of carbon steel and solid alloy.
The fundamental cause of this Alloy 2205 Screws is to alternate the music of a float in piping system, which classifies the space to which there may be an alternate in direction. They also are expressed as a top function of the space from the midpoint line of one-stop of the pipe to the alternative face. Well, it's far pretty identified because the midpoint to stand its distance and is identical to the radius within the route of which the elbow is being twisted. It is significantly utilized in exclusive application in industries like petrochemical, oil & gas, processing, and so on. Duplex Steel WNR 1.4462 Nuts are fabricated and designed by means of the usage of qualitative grade of steel thru the manufacturing methods. The number one application for these products is in heat exchangers and heater coils. It acts as shielding devices, wherein they're being designed to shield pipe-ends of various shapes. We offer this alloy in form of a holly cylinder that has concentric circles in the cylinder’s internal diameter. The top cause of the usage of this steel is to have water resistant connections. They are as nicely used to shut the ends of pneumatic or hydraulic tubes and pipes.
Duplex Steel S31803 Bolts and Screws, ASTM B479 Duplex Steel S32205 Hex Bolts, Duplex SAF 2205 Hex Cap Screws, DSS 1.4462 Hex Head Nut Manufacturers & Suppliers in India.
Duplex Steel 2205 Fasteners Specification
| Specifications | ASTM A479 & ASME SA479 |
| Standard | DIN, ASTM, BS and all International Standards |
| Length | 3 mm to 200 mm |
| Nuts Size | M3 – M56 | 3/6″ to 2″ | Custom Sizes |
| ASTM A182 F51 UNS S31803 Bolts / Screw Size | M3 – M56 | 3/6″ to 2″ | Custom Sizes |
| Standard | DIN, UNI, ISO, JIS, GB, IS, BS, ASME, ANSI, ASTM and all International Standards |
| ASTM A182 F60 UNS S32205 Bolts, Studs Threads: | METRIC, BSW, BSF, UNC, UNF or as required |
| In Form of | Hex, Square, Round, Threading as per Gauge Etc. |
| Head drive | Phillips, Slotted, Phillips/Slot, Six-Lobe, etc |
| Bolts Size | M2, M2.5, M3, M4, M5, M6, M8, M10, M12, M14, M16, M20, M24, M30, M36 to M160 |
| Machine Screws Size | M1.6 – M12 |
| Washers Size | M3 – M56 | 3/6″ to 2″ | Custom Sizes |
| Test Certificate: | Manufacturer Test Certificate as per EN 10204 / 3.1 |
| Source of raw materials | Tata Steel, JSPL, RINL, Usha Martin, Dhamm Steel, Mukund Steel etc. |
| Scope Of Manufacture |
|
| Duplex Steel Grades | Duplex Steel UNS S32205 |
| Packing | IN BULK: canton, pallet, Small Boxs / carton / pallet, or customer request |
| Production process | M2-M24: Cold Froging, hot forging M24-M100, machining and CNC for Customized connecting element |
| Duplex 2205 Fasteners Standard: | ANSI – American National Standards Institute
DIN: DIN 931, DIN 933, DIN 934, DIN 970 UTS – Unified Thread Standard : UNC, UNF, UNEF, UNS, NPT, NPTF ISO – International Organization for Standardization : ISO 4032, ISO 4033, JIS standards |
| Fasteners Type | Cap Screw, Machine Screw, Wing Screw, Spring Washers, Washers, Studs, Marine Anchors, Anchors, Hexagon Nut,U- Bolts, Anchor Bolt, Mushroom Head Square Neck Bolts, J Bolts,Eye Bolt,Structural Bolts, Bolts, Nuts, Sockets, Screws, Allen Cap screw,Nut, Hex Coupling Nut, Hex Nut, Square Nut, Hex Domed Cap Nuts, Hex Head Bolts, Stud Bolts, Socket Hexagon Head Screw, Pan Head Screw, Socket Head Cap Screw, Wing Screw, T-Head Bolts, Foundation Bolts,Screw, Studs, Socket Screw, Hex Set Screw |
Duplex Steel UNS S31803/S32205 Nuts
Duplex Steel UNS S31803/S32205 Bolts
Duplex Steel UNS S31803/S32205 Self Drilling Screws
Duplex Steel UNS S31803/S32205 Panel Nuts
Duplex Steel UNS S31803/S32205 Star Washers
Duplex Steel UNS S31803/S32205 Acorn Nuts
Duplex Steel UNS S31803/S32205 Carriage Bolts
Duplex Steel UNS S31803/S32205 Double Ended Studs
Duplex Steel UNS S31803/S32205 Countersunk Bolts
Duplex Steel UNS S31803/S32205 Hex Coupling Nut
Duplex Steel UNS S31803/S32205 Eye Bolts
Duplex Steel UNS S31803/S32205 Spring Pins
Duplex Steel UNS S31803/S32205 Fasteners Equivalent Grade
| STANDARD | UNS | WERKSTOFF NR. |
| Duplex 2205 | S31803 / S32205 | 1.4462 |
Duplex Steel UNS S31803/S32205 Fasteners Chemical Composition
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N | Fe |
| S31803 | 0.030 max | 2.00 max | 1.00 max | 0.030 max | 0.020 max | 22.0 – 23.0 | 3.0 – 3.5 | 4.50 – 6.50 | 0.14 – 0.20 | 63.72 min |
| S32205 | 0.030 max | 2.00 max | 1.00 max | 0.030 max | 0.020 max | 21.0 – 23.0 | 2.50 – 3.50 | 4.50 – 6.50 | 0.8 – 0.20 | 63.54 min |
Duplex Steel UNS S31803/S32205 Fasteners Mechanical Properties
| Element | Density | Melting Point | Yield Strength (0.2%Offset) | Tensile Strength | Elongation |
| S31803 / S32205 | 7.8 g/cm3 | 1350 °C (2460 °F) | Psi – 80000 , MPa – 550 | Psi – 116000 , MPa – 800 | 15 % |
ASTM / DIN Specification of Duplex Steel UNS S31803/S32205 Fasteners
| ASTM A193 | ASTM A194 | ASTM F2281 |
| ASTM A193M | ASTM A194M | ASTM A962 |
| ASTM A320 | ASTM F593-13a | ASTM A962M |
| ASTM A320M | ASTM F594-15 | |
| DIN 580 | DIN 6914 | DIN 6921 |
| DIN 582 | DIN 3570 | DIN 603 |
| DIN 444 | DIN 7990 | DIN 2510 |
| DIN 939 | DIN 1B | DIN 976 |
| DIN 933 | DIN 529 | DIN 912 |
| DIN 931 | DIN 6325 |
Duplex Steel UNS S32205 Fasteners Weight Chart
| WEIGHTS MACHINE SCREWS & Type 1, 23, F and G TAPPING SCREWS LBS. Per 1000 pieces |
|||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| DIAMETERS | |||||||||||
| LENGTHS | #2 | #3 | #4 | #5 | #6 | #8 | #10 | #12 | 1/4″ | 5/16″ | 3/8″ |
| 1/8 | 0.40 | 0.55 | 0.70 | 1.1 | 1.4 | — | — | — | — | — | — |
| 3/16 | 0.50 | 0.70 | 0.90 | 1.2 | 1.5 | 2.5 | 3.9 | — | — | — | — |
| 1/4 | 0.60 | 0.80 | 1.00 | 1.4 | 1.7 | 2.8 | 4.3 | 5.6 | 8.5 | — | — |
| 5/16 | 0.60 | 0.90 | 1.20 | 1.5 | 1.9 | 3.1 | 4.6 | 6.1 | 9.1 | 16.7 | — |
| 3/8 | 0.70 | 0.90 | 1.30 | 1.7 | 2.1 | 3.4 | 5.0 | 6.5 | 9.8 | 17.7 | 29.2 |
| 7/16 | 0.80 | 1.00 | 1.50 | 1.9 | 2.2 | 3.6 | 5.4 | 6.9 | 10.4 | 18.8 | 30.7 |
| 1/2 | 0.80 | 1.10 | 1.60 | 2.0 | 2.4 | 3.9 | 5.8 | 7.4 | 11.1 | 19.8 | 32.2 |
| 9/16 | 0.90 | 1.20 | 1.70 | 2.2 | 2.6 | 4.2 | 6.2 | 7.8 | 11.7 | 20.9 | 33.6 |
| 5/8 | 1.00 | 1.30 | 1.80 | 2.3 | 2.8 | 4.5 | 6.6 | 8.3 | 12.4 | 21.9 | 35.1 |
| 3/4 | 1.10 | 1.50 | 2.10 | 2.6 | 3.2 | 5.0 | 7.3 | 9.2 | 13.6 | 24.0 | 38.0 |
| 7/8 | 1.30 | 1.70 | 2.30 | 3.0 | 3.5 | 5.6 | 8.1 | 10.1 | 14.9 | 26.1 | 41.0 |
| 1″ | 1.40 | 1.90 | 2.50 | 3.4 | 3.9 | 6.2 | 8.9 | 11.0 | 16.1 | 28.8 | 44.0 |
| 1-1/8″ | 1.50 | 2.00 | 2.80 | 3.8 | 4.3 | 6.7 | 9.6 | 11.9 | 17.4 | 30.2 | 47.0 |
| 1-1/4″ | 1.60 | 2.20 | 3.00 | 4.1 | 4.6 | 7.3 | 10.4 | 12.8 | 18.7 | 32.3 | 49.8 |
| 1-1/2″ | 1.80 | 2.50 | 3.50 | 4.7 | 5.3 | 8.3 | 11.9 | 14.7 | 21.2 | 36.5 | 55.8 |
| 1-3/4″ | 2.10 | 2.90 | 4.00 | 5.3 | 6.1 | 9.4 | 13.5 | 16.5 | 23.7 | 40.7 | 61.7 |
| 2″ | 2.40 | 3.30 | 4.50 | 6.0 | 6.8 | 10.6 | 15.0 | 18.3 | 26.2 | 44.8 | 67.6 |
| 2-1/4″ | 2.60 | 3.60 | 5.00 | 6.7 | 7.6 | 11.8 | 16.6 | 20.1 | 28.8 | 19.0 | 73.5 |
| 2-1/2″ | 2.80 | 3.90 | 5.50 | 7.3 | 8.3 | 12.9 | 18.1 | 22.0 | 31.3 | 53.2 | 79.5 |
| 2-3/4″ | 3.10 | 4.30 | 6.00 | 7.9 | 9.1 | 13.9 | 19.7 | 23.8 | 33.9 | 57.3 | 85.3 |
| 3″ | 3.40 | 4.70 | 6.50 | 8.6 | 9.8 | 15.0 | 21.2 | 25.6 | 36.4 | 61.5 | 91.3 |
| * Weights above are approximate and are based on pan head machine screws | |||||||||||
Duplex Steel UNS S31803/S32205 Fasteners Standard
| Hexagon Bolt / Set Screws | Stud Bolt | Hexagon Nuts | Socket Cap screws |
|---|---|---|---|
| DIN 931 | BS4882 | DIN 934 | DIN 912 |
| DIN 933 | DIN 976 | BS 1768 | DIN 6912 |
| BS 1768 | BS 1769 | DIN 7984 | |
| UNI 5731 | BS 1083 | ANSI B18.3 | |
| UNI 5739 | BS 3692 | ISO 4762 | |
| ISO 4014 | ISO 4032 | UNI 5931 | |
| ISO 4017 | ISO 4033 | BS 2470 | |
| BS 1769 | ANSI B18.2.2 | BS 4168 | |
| BS 3692 | |||
| ANSI B18.2.1 | |||
| Socket & Slotted Set Screws | Socket & Slotted Countersunk Screws | Studs | Washers |
| DIN 913 | DIN 963 | DIN 938 | DIN 125 |
| DIN 914 | DIN 7991 | DIN 939 | DIN 9021 |
| DIN 915 | BS 4168 | DIN 2510 | BS 4320 |
| DIN 916 | BS 1981 | BS 4439 | BS 3410 |
| DIN 551 | BS 483 | BS 2693 | |
| DIN 553 | BS 2470 | Spring Washers | |
| DIN 438 | DIN 127 | ||
| BS 4168 | BS 4464 | ||
| BS 1802 |
Other Types of Duplex Steel UNS S31803/S32205 Fasteners
- DSS UNS S31803 Hex Bolts
- Duplex Steel S32205 T-Head Bolts
- Duplex Grade S31803 Allen Cap Screw
- Duplex 2205 Lag Bolt
- Duplex Stainless Steel S32205 Nuts & Bolt
- High Quality S31803 Duplex Steel Hex Coupling Nut
- Duplex S32205 Heavy Hex Nuts
- ASME SB479 DSS S31803 Heavy Hex Bolts
- Duplex SAF 2205 Hex Bolts
- Duplex Grade S32205 Washers Supplier
- DSS DIN 1.4462 Foundation Bolts
- Duplex Steel S31803 Double Ended Stud
Other Products
Brochures
View our 2020 financial prospectus brochure for an easy to read guide on all of the services offer.